Furnace Repair in Gilbert and the Phoenix Area
Licensed HVAC technicians repair gas and electric furnaces. You get the price before work starts, and emergency calls are answered 24/7.
How furnace repair works
A furnace needs four things to heat your home: a call for heat from the thermostat, fuel or electricity, a safe way to ignite or energize, and airflow to carry the heat. When one of them breaks, the furnace stops or runs badly. Our technician checks them in order. They test the thermostat and its wiring, confirm power and gas supply, then follow the start-up sequence step by step to see where it stops: inducer motor, pressure switch, igniter or pilot, gas valve, flame sensor, blower and limit switches.
That process finds the actual cause rather than swapping parts. You get the price for the repair in writing before any work begins.
Common furnace problems
- Furnace blowing cold air or not heating at all
- Igniter or pilot that will not light or stay lit
- Flame sensor coated with residue, causing short cycles
- Blower motor or capacitor failure
- Dirty filter restricting airflow and tripping the high-limit switch
- Thermostat faults and loose wiring
- Cracked heat exchanger, a safety issue that needs prompt attention
- Strange sounds such as banging, rattling or squealing
Safety first
If you smell gas, leave the home and call your gas utility and emergency services before anything else. If a carbon monoxide detector sounds, get everyone outside and call 911. A yellow, flickering flame instead of a steady blue one, soot around the furnace or a burning smell that persists after the first use of the season should be checked by a technician.
Repair or replace a furnace
Repair is usually right for a failed igniter, flame sensor, motor, capacitor or control board on a furnace that is otherwise in good shape. Replacement deserves a careful look if the heat exchanger is cracked, if the furnace is old and failing in several ways, or if comfort and efficiency are poor. We explain your options and give a free replacement estimate when it makes sense. See our furnace replacement page.
Furnace problems in Arizona
Winters here are short and mild, so many furnaces sit idle for most of the year. Months of summer attic heat, dust and inactivity mean the first cold morning is when weak igniters, dusty burners and dead capacitors show up. Heating season also comes in sudden cold snaps, which can overwhelm a technician's schedule, so a fall tune-up is the best protection. Many homes here use heat pumps rather than furnaces, and we repair those as well. See our heat pump page.
What to expect on the visit
Your technician calls ahead and arrives at the time we gave you. Before touching anything, they ask what you have noticed: when the problem started, whether it happens at certain times of day, and anything that changed recently. Then they test the system rather than guessing, checking airflow, temperatures across the coil, electrical readings and the thermostat's signal. You see the findings in plain language and get a written price for the repair or the options before any work begins. If you approve the work, the diagnostic fee is waived. Most repairs are finished on the first visit because the truck is stocked with the parts that fail most often in Arizona heat. Afterward the technician tests the system again, cleans up, and tells you what to watch for.
Why Elite Pro Services
Elite Pro Services is one licensed, insured company for heating and cooling, plumbing and electrical work, based in Gilbert and serving Gilbert, Chandler, Mesa, Tempe, Scottsdale and Phoenix. Our plumbing license is Arizona ROC CR-37, number 314628, and our HVAC license is CR-39, number 314629. You get the price before work starts, emergency service is available 24 hours a day, 7 days a week, and the same number reaches us for every trade: (480) 788-7473. We would rather explain a repair honestly than sell a replacement you do not need, and we would rather say a replacement is right than keep patching a failing system.
What affects the scope of a furnace repair
Every furnace repair is priced on what is found, which is why we diagnose first and quote before work. The type of furnace, whether the part is common or specialty, how accessible the unit is in your attic, closet or garage, and whether other components are worn all change the job. Older furnaces sometimes need parts that are no longer made, which is one reason we walk you through repair against replacement.
How to prepare for the visit
Clear a path to the furnace, move stored items away from it, note when the problem started and what you have seen, and have your thermostat model and filter size handy if you know them. If there are pets, tell us so they are kept clear of the work area.
Frequently asked questions
Why is my furnace not heating?
Common causes are a thermostat problem, a dirty filter, a failed igniter or flame sensor, a tripped limit switch or a blower problem. A technician can test and tell you which.
Why does my furnace turn on and off repeatedly?
Short-cycling often comes from a dirty flame sensor, a clogged filter or an overheating limit switch. It needs a diagnosis, because it can also point to a cracked heat exchanger.
Is a yellow flame dangerous?
A healthy gas flame is blue. A yellow or flickering flame can mean incomplete combustion and should be checked right away.
Do you repair electric furnaces and heat pumps?
Yes. We repair gas furnaces, electric furnaces and heat pumps.
Can you repair my furnace the same day?
Same-day heating repair is often available. Call (480) 788-7473.
Do you offer emergency heating repair at night?
Yes. We take emergency calls 24 hours a day, 7 days a week.
How can I prevent furnace breakdowns?
Replace the filter regularly, keep vents open and schedule a fall tune-up. See our heating tune-up page.
Related pages
Elite Pro Services serves Gilbert, Chandler, Mesa, Tempe, Scottsdale and Phoenix.
Call (480) 788-7473 Request a free estimate